These Micro Metal 日韩乱码人妻无码中文字幕视频 have high-power, 12 V motors with a stall current of 750 mA and a typical free-run current of 80 mA. They feature long-life carbon brushes and offer approximately the same performance at 12 V as the 6V HPCB versions offer at 6 V, just with half the current draw. The following table shows all of the versions available with the HPCB 6V motor:
Note: Stalling or overloading 日韩乱码人妻无码中文字幕视频 can greatly decrease their lifetimes and even result in immediate damage. The recommended upper limit for instantaneous torque is 2.5 kg⋅cm (35 oz⋅in) for the 380:1 and 1000:1 gearboxes, and 2 kg⋅cm (25 oz⋅in) for all the other gear ratios; we strongly advise keeping applied loads well under this limit. Stalls can also result in rapid (potentially on the order of seconds) thermal damage to the motor windings and brushes, especially for the versions that use high-power (HP and HPCB) motors; a general recommendation for brushed DC motor operation is 25% or less of the stall current.
Versions with other motors are also available. You can use the following selection boxes to choose from all of our Micro Metal 日韩乱码人妻无码中文字幕视频 versions:
Alternatives available with variations in these parameter(s):
gear ratio motor type encoder
Select variant…
Compare all products in this category
Products in category “12V High-Power Carbon Brush (HPCB) Micro Metal 日韩乱码人妻无码中文字幕视频”
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
| motor/brush type |
gearbox |
encoder |
| HPCB 12V: high-power 12V with carbon brushes |
4.995:1 with brass plates |
|
no encoder |
| voltage |
no-load performance |
stall extrapolation* |
| 12 V |
6800 RPM, 100 mA |
0.09 kg⋅cm (1 oz⋅in), 0.75 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
| motor/brush type |
gearbox |
encoder |
| HPCB 12V: high-power 12V with carbon brushes |
4.995:1 with brass plates |
encoder-compatible (extended motor shaft) |
| voltage |
no-load performance |
stall extrapolation* |
| 12 V |
6800 RPM, 100 mA |
0.09 kg⋅cm (1 oz⋅in), 0.75 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
| motor/brush type |
gearbox |
encoder |
| HPCB 12V: high-power 12V with carbon brushes |
9.96:1 with brass plates |
|
no encoder |
| voltage |
no-load performance |
stall extrapolation* |
| 12 V |
3400 RPM, 80 mA |
0.17 kg⋅cm (2.4 oz⋅in), 0.75 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
| motor/brush type |
gearbox |
encoder |
| HPCB 12V: high-power 12V with carbon brushes |
9.96:1 with brass plates |
encoder-compatible (extended motor shaft) |
| voltage |
no-load performance |
stall extrapolation* |
| 12 V |
3400 RPM, 80 mA |
0.17 kg⋅cm (2.4 oz⋅in), 0.75 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
Cables sold separately.
| motor/brush type |
gearbox |
encoder |
| HPCB 12V: high-power 12V with carbon brushes |
9.96:1 with brass plates |
|
12 CPR incremental quadrature with back connector |
| voltage |
no-load performance |
stall extrapolation* |
| 12 V |
3400 RPM, 80 mA |
0.17 kg⋅cm (2.4 oz⋅in), 0.75 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
Cables sold separately.
| motor/brush type |
gearbox |
encoder |
| HPCB 12V: high-power 12V with carbon brushes |
9.96:1 with brass plates |
|
12 CPR incremental quadrature with side connector |
| voltage |
no-load performance |
stall extrapolation* |
| 12 V |
3400 RPM, 80 mA |
0.17 kg⋅cm (2.4 oz⋅in), 0.75 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
| motor/brush type |
gearbox |
encoder |
| HPCB 12V: high-power 12V with carbon brushes |
15.25:1 with brass plates |
|
no encoder |
| voltage |
no-load performance |
stall extrapolation* |
| 12 V |
2200 RPM, 80 mA |
0.25 kg⋅cm (3.5 oz⋅in), 0.75 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
| motor/brush type |
gearbox |
encoder |
| HPCB 12V: high-power 12V with carbon brushes |
15.25:1 with brass plates |
encoder-compatible (extended motor shaft) |
| voltage |
no-load performance |
stall extrapolation* |
| 12 V |
2200 RPM, 80 mA |
0.25 kg⋅cm (3.5 oz⋅in), 0.75 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
Cables sold separately.
| motor/brush type |
gearbox |
encoder |
| HPCB 12V: high-power 12V with carbon brushes |
15.25:1 with brass plates |
|
12 CPR incremental quadrature with back connector |
| voltage |
no-load performance |
stall extrapolation* |
| 12 V |
2200 RPM, 80 mA |
0.25 kg⋅cm (3.5 oz⋅in), 0.75 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
Cables sold separately.
| motor/brush type |
gearbox |
encoder |
| HPCB 12V: high-power 12V with carbon brushes |
15.25:1 with brass plates |
|
12 CPR incremental quadrature with side connector |
| voltage |
no-load performance |
stall extrapolation* |
| 12 V |
2200 RPM, 80 mA |
0.25 kg⋅cm (3.5 oz⋅in), 0.75 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
| motor/brush type |
gearbox |
encoder |
| HPCB 12V: high-power 12V with carbon brushes |
29.86:1 with brass plates |
|
no encoder |
| voltage |
no-load performance |
stall extrapolation* |
| 12 V |
1100 RPM, 80 mA |
0.39 kg⋅cm (5.4 oz⋅in), 0.75 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
| motor/brush type |
gearbox |
encoder |
| HPCB 12V: high-power 12V with carbon brushes |
29.86:1 with brass plates |
encoder-compatible (extended motor shaft) |
| voltage |
no-load performance |
stall extrapolation* |
| 12 V |
1100 RPM, 80 mA |
0.39 kg⋅cm (5.4 oz⋅in), 0.75 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
Cables sold separately.
| motor/brush type |
gearbox |
encoder |
| HPCB 12V: high-power 12V with carbon brushes |
29.86:1 with brass plates |
|
12 CPR incremental quadrature with back connector |
| voltage |
no-load performance |
stall extrapolation* |
| 12 V |
1100 RPM, 80 mA |
0.39 kg⋅cm (5.4 oz⋅in), 0.75 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
Cables sold separately.
| motor/brush type |
gearbox |
encoder |
| HPCB 12V: high-power 12V with carbon brushes |
29.86:1 with brass plates |
|
12 CPR incremental quadrature with side connector |
| voltage |
no-load performance |
stall extrapolation* |
| 12 V |
1100 RPM, 80 mA |
0.39 kg⋅cm (5.4 oz⋅in), 0.75 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
| motor/brush type |
gearbox |
encoder |
| HPCB 12V: high-power 12V with carbon brushes |
51.45:1 with brass plates |
|
no encoder |
| voltage |
no-load performance |
stall extrapolation* |
| 12 V |
650 RPM, 80 mA |
0.67 kg⋅cm (9.3 oz⋅in), 0.75 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
| motor/brush type |
gearbox |
encoder |
| HPCB 12V: high-power 12V with carbon brushes |
51.45:1 with brass plates |
encoder-compatible (extended motor shaft) |
| voltage |
no-load performance |
stall extrapolation* |
| 12 V |
650 RPM, 80 mA |
0.67 kg⋅cm (9.3 oz⋅in), 0.75 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
Cables sold separately.
| motor/brush type |
gearbox |
encoder |
| HPCB 12V: high-power 12V with carbon brushes |
51.45:1 with brass plates |
|
12 CPR incremental quadrature with back connector |
| voltage |
no-load performance |
stall extrapolation* |
| 12 V |
650 RPM, 80 mA |
0.67 kg⋅cm (9.3 oz⋅in), 0.75 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
Cables sold separately.
| motor/brush type |
gearbox |
encoder |
| HPCB 12V: high-power 12V with carbon brushes |
51.45:1 with brass plates |
|
12 CPR incremental quadrature with side connector |
| voltage |
no-load performance |
stall extrapolation* |
| 12 V |
650 RPM, 80 mA |
0.67 kg⋅cm (9.3 oz⋅in), 0.75 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
| motor/brush type |
gearbox |
encoder |
| HPCB 12V: high-power 12V with carbon brushes |
75.81:1 with brass plates |
|
no encoder |
| voltage |
no-load performance |
stall extrapolation* |
| 12 V |
450 RPM, 80 mA |
1.0 kg⋅cm (13 oz⋅in), 0.75 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
| motor/brush type |
gearbox |
encoder |
| HPCB 12V: high-power 12V with carbon brushes |
75.81:1 with brass plates |
encoder-compatible (extended motor shaft) |
| voltage |
no-load performance |
stall extrapolation* |
| 12 V |
450 RPM, 80 mA |
1.0 kg⋅cm (13 oz⋅in), 0.75 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
Cables sold separately.
| motor/brush type |
gearbox |
encoder |
| HPCB 12V: high-power 12V with carbon brushes |
75.81:1 with brass plates |
|
12 CPR incremental quadrature with back connector |
| voltage |
no-load performance |
stall extrapolation* |
| 12 V |
450 RPM, 80 mA |
1.0 kg⋅cm (13 oz⋅in), 0.75 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
Cables sold separately.
| motor/brush type |
gearbox |
encoder |
| HPCB 12V: high-power 12V with carbon brushes |
75.81:1 with brass plates |
|
12 CPR incremental quadrature with side connector |
| voltage |
no-load performance |
stall extrapolation* |
| 12 V |
450 RPM, 80 mA |
1.0 kg⋅cm (13 oz⋅in), 0.75 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
| motor/brush type |
gearbox |
encoder |
| HPCB 12V: high-power 12V with carbon brushes |
100.37:1 with brass plates |
|
no encoder |
| voltage |
no-load performance |
stall extrapolation* |
| 12 V |
330 RPM, 80 mA |
1.3 kg⋅cm (18 oz⋅in), 0.75 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
| motor/brush type |
gearbox |
encoder |
| HPCB 12V: high-power 12V with carbon brushes |
100.37:1 with brass plates |
encoder-compatible (extended motor shaft) |
| voltage |
no-load performance |
stall extrapolation* |
| 12 V |
330 RPM, 80 mA |
1.3 kg⋅cm (18 oz⋅in), 0.75 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
Cables sold separately.
| motor/brush type |
gearbox |
encoder |
| HPCB 12V: high-power 12V with carbon brushes |
100.37:1 with brass plates |
|
12 CPR incremental quadrature with back connector |
| voltage |
no-load performance |
stall extrapolation* |
| 12 V |
330 RPM, 80 mA |
1.3 kg⋅cm (18 oz⋅in), 0.75 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
Cables sold separately.
| motor/brush type |
gearbox |
encoder |
| HPCB 12V: high-power 12V with carbon brushes |
100.37:1 with brass plates |
|
12 CPR incremental quadrature with side connector |
| voltage |
no-load performance |
stall extrapolation* |
| 12 V |
330 RPM, 80 mA |
1.3 kg⋅cm (18 oz⋅in), 0.75 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
| motor/brush type |
gearbox |
encoder |
| HPCB 12V: high-power 12V with carbon brushes |
150.58:1 with brass plates |
|
no encoder |
| voltage |
no-load performance |
stall extrapolation* |
| 12 V |
220 RPM, 80 mA |
1.8 kg⋅cm (24 oz⋅in), 0.75 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
| motor/brush type |
gearbox |
encoder |
| HPCB 12V: high-power 12V with carbon brushes |
150.58:1 with brass plates |
encoder-compatible (extended motor shaft) |
| voltage |
no-load performance |
stall extrapolation* |
| 12 V |
220 RPM, 80 mA |
1.8 kg⋅cm (24 oz⋅in), 0.75 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
Cables sold separately.
| motor/brush type |
gearbox |
encoder |
| HPCB 12V: high-power 12V with carbon brushes |
150.58:1 with brass plates |
|
12 CPR incremental quadrature with back connector |
| voltage |
no-load performance |
stall extrapolation* |
| 12 V |
220 RPM, 80 mA |
1.8 kg⋅cm (24 oz⋅in), 0.75 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
Cables sold separately.
| motor/brush type |
gearbox |
encoder |
| HPCB 12V: high-power 12V with carbon brushes |
150.58:1 with brass plates |
|
12 CPR incremental quadrature with side connector |
| voltage |
no-load performance |
stall extrapolation* |
| 12 V |
220 RPM, 80 mA |
1.8 kg⋅cm (24 oz⋅in), 0.75 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
| motor/brush type |
gearbox |
encoder |
| HPCB 12V: high-power 12V with carbon brushes |
210.59:1 with brass plates |
|
no encoder |
| voltage |
no-load performance |
stall extrapolation* |
| 12 V |
160 RPM, 80 mA |
2.5 kg⋅cm (34 oz⋅in), 0.75 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
| motor/brush type |
gearbox |
encoder |
| HPCB 12V: high-power 12V with carbon brushes |
210.59:1 with brass plates |
encoder-compatible (extended motor shaft) |
| voltage |
no-load performance |
stall extrapolation* |
| 12 V |
160 RPM, 80 mA |
2.5 kg⋅cm (34 oz⋅in), 0.75 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
Cables sold separately.
| motor/brush type |
gearbox |
encoder |
| HPCB 12V: high-power 12V with carbon brushes |
210.59:1 with brass plates |
|
12 CPR incremental quadrature with back connector |
| voltage |
no-load performance |
stall extrapolation* |
| 12 V |
160 RPM, 80 mA |
2.5 kg⋅cm (34 oz⋅in), 0.75 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
Cables sold separately.
| motor/brush type |
gearbox |
encoder |
| HPCB 12V: high-power 12V with carbon brushes |
210.59:1 with brass plates |
|
12 CPR incremental quadrature with side connector |
| voltage |
no-load performance |
stall extrapolation* |
| 12 V |
160 RPM, 80 mA |
2.5 kg⋅cm (34 oz⋅in), 0.75 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
| motor/brush type |
gearbox |
encoder |
| HPCB 12V: high-power 12V with carbon brushes |
248.98:1 with brass plates |
|
no encoder |
| voltage |
no-load performance |
stall extrapolation* |
| 12 V |
130 RPM, 80 mA |
3.0 kg⋅cm (41 oz⋅in), 0.75 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
| motor/brush type |
gearbox |
encoder |
| HPCB 12V: high-power 12V with carbon brushes |
248.98:1 with brass plates |
encoder-compatible (extended motor shaft) |
| voltage |
no-load performance |
stall extrapolation* |
| 12 V |
130 RPM, 80 mA |
3.0 kg⋅cm (41 oz⋅in), 0.75 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
Cables sold separately.
| motor/brush type |
gearbox |
encoder |
| HPCB 12V: high-power 12V with carbon brushes |
248.98:1 with brass plates |
|
12 CPR incremental quadrature with back connector |
| voltage |
no-load performance |
stall extrapolation* |
| 12 V |
130 RPM, 80 mA |
3.0 kg⋅cm (41 oz⋅in), 0.75 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
Cables sold separately.
| motor/brush type |
gearbox |
encoder |
| HPCB 12V: high-power 12V with carbon brushes |
248.98:1 with brass plates |
|
12 CPR incremental quadrature with side connector |
| voltage |
no-load performance |
stall extrapolation* |
| 12 V |
130 RPM, 80 mA |
3.0 kg⋅cm (41 oz⋅in), 0.75 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
| motor/brush type |
gearbox |
encoder |
| HPCB 12V: high-power 12V with carbon brushes |
297.92:1 with brass plates |
|
no encoder |
| voltage |
no-load performance |
stall extrapolation* |
| 12 V |
110 RPM, 80 mA |
3.3 kg⋅cm (45 oz⋅in), 0.75 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
| motor/brush type |
gearbox |
encoder |
| HPCB 12V: high-power 12V with carbon brushes |
297.92:1 with brass plates |
encoder-compatible (extended motor shaft) |
| voltage |
no-load performance |
stall extrapolation* |
| 12 V |
110 RPM, 80 mA |
3.3 kg⋅cm (45 oz⋅in), 0.75 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
Cables sold separately.
| motor/brush type |
gearbox |
encoder |
| HPCB 12V: high-power 12V with carbon brushes |
297.92:1 with brass plates |
|
12 CPR incremental quadrature with back connector |
| voltage |
no-load performance |
stall extrapolation* |
| 12 V |
110 RPM, 80 mA |
3.3 kg⋅cm (45 oz⋅in), 0.75 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
Cables sold separately.
| motor/brush type |
gearbox |
encoder |
| HPCB 12V: high-power 12V with carbon brushes |
297.92:1 with brass plates |
|
12 CPR incremental quadrature with side connector |
| voltage |
no-load performance |
stall extrapolation* |
| 12 V |
110 RPM, 80 mA |
3.3 kg⋅cm (45 oz⋅in), 0.75 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
| motor/brush type |
gearbox |
encoder |
| HPCB 12V: high-power 12V with carbon brushes |
379.17:1 with high-durability steel plates |
|
no encoder |
| voltage |
no-load performance |
stall extrapolation* |
| 12 V |
85 RPM, 80 mA |
5.0 kg⋅cm (69 oz⋅in), 0.75 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
| motor/brush type |
gearbox |
encoder |
| HPCB 12V: high-power 12V with carbon brushes |
379.17:1 with high-durability steel plates |
encoder-compatible (extended motor shaft) |
| voltage |
no-load performance |
stall extrapolation* |
| 12 V |
85 RPM, 80 mA |
5.0 kg⋅cm (69 oz⋅in), 0.75 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
Cables sold separately.
| motor/brush type |
gearbox |
encoder |
| HPCB 12V: high-power 12V with carbon brushes |
379.17:1 with high-durability steel plates |
|
12 CPR incremental quadrature with back connector |
| voltage |
no-load performance |
stall extrapolation* |
| 12 V |
85 RPM, 80 mA |
5.0 kg⋅cm (69 oz⋅in), 0.75 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
Cables sold separately.
| motor/brush type |
gearbox |
encoder |
| HPCB 12V: high-power 12V with carbon brushes |
379.17:1 with high-durability steel plates |
|
12 CPR incremental quadrature with side connector |
| voltage |
no-load performance |
stall extrapolation* |
| 12 V |
85 RPM, 80 mA |
5.0 kg⋅cm (69 oz⋅in), 0.75 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
| motor/brush type |
gearbox |
encoder |
| HPCB 12V: high-power 12V with carbon brushes |
986.41:1 with brass plates |
|
no encoder |
| voltage |
no-load performance |
stall extrapolation* |
| 12 V |
35 RPM, 80 mA |
10 kg⋅cm (138 oz⋅in), 0.75 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
| motor/brush type |
gearbox |
encoder |
| HPCB 12V: high-power 12V with carbon brushes |
986.41:1 with brass plates |
encoder-compatible (extended motor shaft) |
| voltage |
no-load performance |
stall extrapolation* |
| 12 V |
35 RPM, 80 mA |
10 kg⋅cm (138 oz⋅in), 0.75 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
Cables sold separately.
| motor/brush type |
gearbox |
encoder |
| HPCB 12V: high-power 12V with carbon brushes |
986.41:1 with brass plates |
|
12 CPR incremental quadrature with back connector |
| voltage |
no-load performance |
stall extrapolation* |
| 12 V |
35 RPM, 80 mA |
10 kg⋅cm (138 oz⋅in), 0.75 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
Cables sold separately.
| motor/brush type |
gearbox |
encoder |
| HPCB 12V: high-power 12V with carbon brushes |
986.41:1 with brass plates |
|
12 CPR incremental quadrature with side connector |
| voltage |
no-load performance |
stall extrapolation* |
| 12 V |
35 RPM, 80 mA |
10 kg⋅cm (138 oz⋅in), 0.75 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
Cables sold separately.
| motor/brush type |
gearbox |
encoder |
| HPCB 12V: high-power 12V with carbon brushes |
4.995:1 with brass plates |
|
12 CPR incremental quadrature with back connector |
| voltage |
no-load performance |
stall extrapolation* |
| 12 V |
6800 RPM, 100 mA |
0.09 kg⋅cm (1 oz⋅in), 0.75 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.
Cables sold separately.
| motor/brush type |
gearbox |
encoder |
| HPCB 12V: high-power 12V with carbon brushes |
4.995:1 with brass plates |
|
12 CPR incremental quadrature with side connector |
| voltage |
no-load performance |
stall extrapolation* |
| 12 V |
6800 RPM, 100 mA |
0.09 kg⋅cm (1 oz⋅in), 0.75 A |
| * Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
